HI BOND ADHESIVE epigen 0911

Quantity: In Stock

Category: Adhesives & High Strength Glues

Quick Overview:

A high strength multipurpose paste suitable for grouting and caulking, designed for use on a variety of surfaces including steel, concrete, timber and fibreglass.
Characterised by exceptional toughness and durability, use has extended to ceramic wear tile bedding and grouting, fairing blowholes on concrete, and pitting on steel surfaces prior to coating.
Epigen 911 possesses exceptional water resistance and resistance to a broad range of chemicals including degreasers, cleaners, aviation fuels and lubricants, and a range of acid and alkali reagents.

  • Ceramic Wear Tile Adhesive
  • Applying Fillets and Aris to Steel Surfaces
  • Fairing Pitting and Hollows on Steel Tanks
  • Pile Capping
  • Concrete Crack and Void Repair
  • Anti Corrosion Barrier Lining

  • Excellent chemical resistance
  • Food industry suitable
  • Non sag viscosity for easy installation
  • Free of all solvents - zero VOC
  • Tough and durable
  • Versatility in application allows concrete patching
  • Suitable on steel to void fill or fair surfaces
  • Strongly adhesive for optimum adhesion
Epigen 911 is supplied as a two part kit comprising component “A” resin, and component “B” curative.
The entire kit is supplied in a pre weighed convenient size to make on site activities easier.
Peerless Industrial Systems can provide information on specific applications based on industry acceptable practices or historical results.

Colour Off White      
Ratio by weight 1 kg Component “A”    
  1 kg Component “B”
Pot Life minutes @ 24oC 30      
Mixed consistency @ 24oC Paste       
Specific gravity when mixed 1.4      
Coverage /m 2 @ 10mm 14 kg      
Compressive strength ASTM D695, Mpa 70
Tensile strength ASTM D638, Mpa 18
Flexural strength ASTM D790, Mpa 32
Hardness, Shore D >85
Elongation ASTM D638, % 1.0
Tensile Adhesion ASTM 4541, MPa >12
Thermal conductivity ASTM C177, Kcal/m.hrC 0.6
Coeff of Therm Exp ASTM C531, 10-5/C 2.0
Maximum exposure temperature, C 120
Heat deflection temperature ASTM D648, C 75
Thin Film Gel @ 1mm, Minutes 180
Thin Film Set @ 1mm, Minutes 240
Ultimate cure time, Hours 96

SURFACE PREPARATION                                                          
Methods for surface preparation prior to use include using chemical means such as washing & etching, high pressure water blasting, or mechanical techniques such as abrasive blasting, grinding or scarifying.                          
Specialist advice is available from Peerless Industrial Systems to ensure the correct preparation procedure is employed for specific application.                                      
Mixing of product should be carried out using spatula or by slow speed blender, and completed by adding to the component “A”, component “B”. Ensure the mix is homog- enous and even in colour.                            
In all cases, the minimum depth should be nominally 2mm to ensure sufficent adhesive is in place and afford reasonable compressive strength. There is no maximum thickness reqirement. No primer is required to facilitate adhesion unless the surface is loose or friable. In cool environments, pre warm the product before use.      
Adhesive Applications:                                                            
Apply a thin coat of Epigen 911 to both surfaces before bringing the two together. Do not use where a flexible or resilient glue line is required. Recommended where strength or heavy shock resistant is required (eg: Ceramic Tiles to Steel on chutes, steel onto steel, concrete onto steel). Preheat the material before use to achieve best cure rate and strength.
Crack Repairs:                                                            
In horizontal installations, open up cracks using a grinder before applying directly into crack. In vertical installations, use an abrasive bit on a drill and follow the crack keeping the surface shoulders narrow.                            

Bedding Application - nominally 5mm thickness 
7kg = 1000mm X 1000mm X 5mm  
Adhesive or Void Filling Application   
1.4kg = 1 litre      
1.4kg = 100mm X 100mm X 100mm  

Tested at 21oC. Samples cured for 10 days at 25oC. Curing at elevated temperatures will improve chemical resistance.
1 = Continuous or long term immersion
2 = Short term immersion
3 = Splash and spills
4 = Avoid contact



Acetic Acid, 10 % 2 Acetone 2
Acetic Acid, Glacial 2 Ammonium Chloride 1
Hydrochloric Acid, 5 % 1 Beer 1
Hydrochloric Acid, 10 % 2 Dichloromethane 4
Hydrochloric Acid, conc 2 Diesel Fuel 1
Nitric Acid, 5 %  2 Isopropyl Alcohol 2
Nitric Acid, 10 % 2 Kerosene 1
Phosphoric Acid, 5 % 1 Petrol 2
Phosphoric Acid, 20 % 2 Salt Water 1
Sulfuric Acid, 5 % 3 Sewage 2
Sulfuric Acid, 20 % 3 Skydrol 2
Ammonium Hydroxide, 5 % 1 Sodium Cyanide 1
Ammonium Hydroxide, 20 % 1 Sodium Hypochlorite 2
Potassium Hydroxide, 5 % 1 Toluene 2
Potassium Hydroxide, 20 % 1 Trichloroethane 3
Sodium Hydroxide, 5 % 1 Wine 2
Sodium Hydroxide, 20 % 1 Xylene 2


Variations in cure may arise due to the amount of material being applied, the thickness of material being applied, the surface temperature, and the product temperature. The cure may be increased by heating product or by leaving mixed material stand for 15 minutes before use. The cure may be decreased by cooling the product before mixing.

Share: Messenger

Sorry, Currently No Video Uploaded.
Sorry, Currently No File Uploaded.

HI BOND ADHESIVE epigen 0911

Please Leave Your Product Enquiry Here. We will Get Back To You Soon.

Product Specifications

  • Product SKU : -
  • Weight (GRAM) : -
  • Dimension : -

Locate Us